Second Hand TEM Machine P350 / 320 x 300

P350 machine

Rapid and cost-effective production deburring

The fast and reliable P350 machine is the best
solution for removing all internal and external burrs
simultaneously in a single operation. The P350
is designed to accommodate medium- to large production
volumes, as well as handle a variety
of difficult to deburr workpieces.
Available in two different chamber sizes with a
clamping force of 3.5 MN, the P350 delivers long
service life and consistent part quality even in three
shift operational environments.

Machine Specification
Year of manufcture 2013
New Deburring Chamber size 320 x 300
General refurbished
1 Year warranty
Sound Reducing Enclosure new painted
Siemens Control S7 -315 PLC, new HMI 15“ Touchpanel
5 closing plates refurbished
New gas dosing cylinder
New Hydraulic tubes
NEW TÜV
New yearly maintenance
No gas compressor
Availibility of machine after downpayment from customer 5 month

Used Thermal Deburring Machine

C250 TEM Machine

Fully rebuiltsold

Will fit 7”, 8”, 10” or 11” size chamber

5 stations machine

Additional Accessories available

12 months warranty

Machine Clamping Pressure. 250 Ton (2.2MN)
Machine Size (W x D x H)
Including exhaust blower
66.0 in x 162.0 in x 116 in
(1677mm x 4115mm x 2946mm
Transport Weight:
TEM Machine
Hydraulic Power Unit

15,000 lbs. (6,820 kg)
1,600 lbs. (728 kg)
Power Requirements
480 VAC, 3-phase, 60 Hz
Fuel Gas Types
Natural Gas or Grade 2.0 Bottled Methane (CH4) and Oxygen 99.5% Clean or Higher (O2)
Control and Valve Voltage
110 VAC / 24 VDC (Depending on unit)
Cooling Water Requirements:
  
Machine
Hydraulic Power Unit
72°F(22.2°C) Max / 62°F(16°C) Min
300 Micron Clean
 
0.5 in. NPT 2.5 gpm (11.4 Lpm), 50 psi (3.5 bar)
0.75 in. NPT 4 gpm (15.2 Lpm), 50 psi (3.5 bar)
Hydraulic Pump
20 gpm (76 Lpm) 1,600 psi (112 bar)
Hydraulic Fluid
100 gal (378 liter) Mobil DTE25 or equivalent
Lubrication System
Mobil XHP-222 or equivalent
Noise Levels
85 dBA Time Weighted Average
MaterialNatural Gas Pressure
Steel8-20 bar (116-290 psi)
Cast Iron5-20 bar (73-290 psi)
Zinc5-10 bar (73-145 psi)
Aluminum5-10 bar (73-145 psi)
Brass8-25 bar (116-363 psi)

Used Abrasive Flow Machining Machine.

ECOFLOW 100 Machine

The ECOFLOW series machines are specifically designed for the small die maker or job shop owner.  It is the idealsold economical alternative for processing carbide dies for precise and repeatable surface finish improvement as well as short-run polishing and radiusing of surfaces and edges of critical components.

ECOFLOW is the solution when there can be no compromise in edge and surface improvement conditioning.

Status new – show room machine

Model                                 ECOFLOW 100

Cylinder size                      100mm ( 3.8-inch)

Media Stroke                     250mm

Max Pressure                    140 bar (2000 psi)

PLC/HMI                             Siemens PLC and A 5.7” Siemens touchscreen

Line Voltage                       406Vac

UA-73818232-1